Heat Shrink-ability Thermal shrinkage ratio: 2:1 The wall thickness of braided pipe after full shrinkage is about 1.0 mm Longitudinal change after complete contraction: - 10 ~ - 20% Temperature Grade Operating temperature range (3000 hours): - 40 ℃ ~ 125 ℃ Service temperature range (1000 hours): - 40 ℃ ~ 150 ℃ Minimum shrinkage temperature: 110 ℃ Recommended shrinkage temperature: 120 ℃ ~ 150 ℃ Maximum storage temperature: 50 ℃ Materials Warp material: polyester multifilament Latitudinal material: irradiation crosslinking, modified polyolefin (PE-7042) Coating material: modified polyolefin Basic performance Performance TEST RESULT Wear resistance: (200g load, 0.3mm metal knife edge, 10Hz, 10min stroke, 144000 cycles) 23℃ The protected rubber pipe fittings are not worn 80℃ The protected rubber pipe fittings are not worn 125℃ The protected rubber pipe fittings are not worn Thermal aging property 168小时，125 ℃ The wear resistance is not weakened at 23 ℃ 24小时，150 ℃ The wear resistance is not weakened at 23 ℃ Flame retardancy MVSS 302 Uncracked Low temperature flexibility -40℃ 4 hours Uncracked Solvent resistance: 1. Antifreeze (50% glycol) 2. Engine oil (SAE 10W / 30) 3. Mineral hydraulic fluid 4. Detergent (1% active agent) 5. Brake oil (DOT 4) 6. Unleaded gasoline 7. Diesel oil Soak at 23 ℃ for 24 hours The wear resistance is not weakened at 23 ℃

Dear All Customers and Friends, Happy new year! Our factory will be on holidays from Feb 11th to 19th for chinese new year. Hope to provide you with better service and better products in the new year. Anhui Parker New Material Co.,Ltd

Custom Basalt Insulating Tape with Stainless Steel Wire Insert we can make custom design basalt insulating tape, insert with 1 to 10 pcs stainless steel wire width 20 to 1000 mm thickness 0.8 to 5 mm roll length 1 to 100m

We Anhui Parker New Material Co.,Ltd offer different solutions for exhaust pipe heat protection. Outside aluminum foil exhaust pipe heat protection sleeve made by aluminum foil and glass fibre. Inside is basalt exhaust knitted sleeve. Aluminum foil heat protection sleeve ID 6mm to 160 mm. Basalt exhaust knitted sleeve ID 1" to 6". All materials pass customer tests. They are good solutions for Engine & Generator Exhaust Pipe Protection.

What is thermal conductivity? The thermal conductivity refers to the heat transferred through an area of 1m2 in 1s (not 1H) in a 1m thick material with a temperature difference of 1 degree (k, ℃) on both sides of the surface under the condition of stable heat transfer. The unit is watt / meter · degree (w / (m · k), where k can be replaced by ℃. The thermal conductivity of different substances is different; the thermal conductivity of the same substance is related to its own structure, density, humidity, temperature, pressure and other factors. It is also related to the state of matter. Is the bigger the thermal conductivity the better or the smaller? If it’s a heat dissipating material, the bigger the better. If it’s a heat insulating material, the smaller the better. The lower the thermal conductivity, the better the heat preservation. High Temperature Hose Sleeve Firesleeve with a thermal conductivity of 0.13w/m · degree (w / (m · K), is a good high temperature resistant insulation material. High Temperature Hose Sleeve Firesleeve is used to protect hydraulic hoses, pipes, cables and wires as well as other key components from high temperature, sparks and direct flame. Molten metal splashes deflect at 1200 ℃, while providing constant thermal protection at 560 ℃.